Showing results: 2281 - 2295 of 2604 items found.
-
BXL Series -
IBEKO Power AB
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
Photo Emission Tech., Inc.
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
TOMSAD
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
TOMSAD
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
TOMSAD
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
SG2008 -
Shanghai Jiuzhi Electric Co., Ltd.
SG2008 Automatic 12kV Capacitance & Dissipation Factor Test Set is designed to measure dissipation (tgδ) and capacitance (C) in heavy electromagnetic interference environment such as in power plants or substations. Also it can be used in laboratory for high accurate test such asHigh Voltage (EHV) class Bushings, Windings of transformer (1/2/3 windings), shunt reactors, Current Transformer, Capacitor Voltage transformer(CVT), grading capacitors of Circuit Breakers, Surge Arrester and other electrical equipments. The test set is all-in-one structure: including precision digital bridge, 12kV/200mA frequency conversion power unit, reference capacitor (CN), and other electronic circuits. An external power supply can expand the test range. True portability is realized by the lightweight. Simple usage is realized by the full automation. High performance is realized by the digital process.
-
RMO-G Series -
IBEKO Power AB
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing personnel.The RMO800G is the most powerful portable micro-ohmmeter on the market with 800 A output current. RMO200G is our best seller in the USA. A user can choose the appropriate model depending on the output current requirement, from 100 A (RMO100G) to 800 A (RMO800G).We use an unbreakable plastic case with IP67 protective rating (with closed lid) for instruments’ housing. Although very portable and lightweight, RMO-G micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents. Consequently, it enables the usage of thinner/longer test cables. RMO-G generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. During the testing, it increases current before measuring and decreases current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.Special current clamps measure a current through groundings when the instrument tests in Both Sides Grounded conditions. The instrument itself powers these clamps. If even higher safety level is required, the Remote Control feature enables the operator to perform measurements from distant locations.RMO-G instruments can store up to 500 measurements in internal memory. Also, they have a built-in thermal printer and USB flash drive available as an option. An additional option is the built-in High Precision module suitable for measurement of very low resistance, in the range from 1 to 30 µΩ, with 0,01 µΩ resolution.Our free DV Win software communicates with the RMO-G micro-ohmmeters via USB or RS232 interface. It allows a user to run the test remotely from a PC. Also, a user can download test results, analyze and generate fully configurable test reports through the software.
-
RMO-A Series -
IBEKO Power AB
The RMO-A is a portable micro-ohmmeter designed for contact resistance measurements of switchgear during manufacturing, commissioning and maintenance stages. This micro-ohmmeter is widely used by medium and high-voltage circuit breakers manufacturers. Other typical applications are testing of disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. It accurately measures not only in factory environments but also in high-induction fields and substationsThe RMO-A series contains 6 models, rated from 100 A (RMO100A) to 600 A (RMO600A). The RMO500A (formerly CPM500) is our best seller, with 500 A ripple-free current and weighs only 8 kg.Although placed in a very portable and lightweight metal housing, RMO-A micro-ohmmeters have very high output power capabilities. They can generate 600 A test current continuously for up to 20 s. You can test with current up to 100 A without rest time. High output voltage enables a wider measurement range at the highest test currents, as well as the use of thinner/longer test cables. For testing with 100 A, 20 m test leads can be provided with only 16 mm2 cross-section.RMO-A micro-ohmmeter generates a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the RMO-A ramps up with increasing current before measuring and decreasing current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.An additional option is a built-in High Precision module suitable for measurement of very low resistances, ranges from 1 to 30 µΩ, with 0,01 µΩ resolution.These instruments can store up to 500 measurements in internal memory. A built-in thermal printer is available as an option.Our free DV Win software communicates with the RMO-A micro-ohmmeters via USB or RS232 interface. It allows you to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.
-
M9822/M9822B -
Lisun Electronics Inc.
M9822/M9822B is newly designed circuit adopts rapid AD and DA technology to achieve rapid measurements with high accuracy. And the resolution of 0.1mV/0.1mA can effectively display the minor change of voltage and current, so the instrument has a wider application field and achieves better test results. Meanwhile your operation becomes much more comfortable and easy by equipping the high-light VFD, the simple menu and displayed contents and the operation state indicators on all keys. Otherwise the complete and humanized test functions will greatly improve your productivity.
-
PW-3063R -
PINTEK Electronics
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-3063R as high as 0.1v and 0.01A.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
APCI-1500 -
TEAM SOLUTIONS, INC.
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
APCI-1500-LAC -
TEAM SOLUTIONS, INC.
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
FMWGN1001 -
Fairview Microwave Inc.
FMWGN1001 is a K Band Waveguide Gunn Oscillator with a Center Frequency of 24.125 GHz and a Tuning Range of +/- 1.0 GHz. The unit has a Phase Noise @ 100kHz Offset of -95 dBc/Hz typ and Frequency Stability of -0.4 MHz/°C max. The Gun Oscillator has an Output Power of 10 dBm min and Power Stability of -0.04 dB/°C max. The Waveguide Gun Oscillator uses a Bias Voltage of 5.0 Volts and a Bias Current of 200 mA and has a Waveguide Size of WR-42 with a UG-595/U Flange.
-
IT6300 Series -
I-TECH Electronic Co., Ltd
IT6300 series is high-performance programmable triple channels DC power supply, each output voltage and current can be setfrom0 tomaximum rated output.This series provides series connection, parallelconnectionand synchronous functions ofchannel, which offer multi-purpose solutions forcustomerstest.IT6300 seriesis with high resolution1mV / 1mAand remote sense function, which make the test more accurate. Withbuilt-in standard USB / RS232 / GPIB communication interface,IT6300 seriesgreatly enhance the communication speed, and customersalsocanadjust the digital step value byusing the cursorto to facilitate the operation.
-
Kiwa Dare
Calibrations of electronic equipment is one of the activities that Kiwa Dare offers to its clients. these calibrations are under accreditation in the field of electrical quantities. Besides calibrations in the field of DC current, DC voltage and low frequency (test and measuring) equipment, Kiwa Dare is specialized in calibrating high frequency measuring equipment and in particular EMC equipment in a frequency range of (DC) 40 GHz. New the site validation calibrations whereby Kiwa Dare can calibrate shielded rooms (Faraday room) and anechoic chambers under accreditation.
